Kent / AMCO Cold Water and Chemical Meters
from www.watermeters.com
 
Kent / AMCO C-700 Positive Displacement Water Meters
The Kent / AMCO C700 oscillating piston type water meters are the most advanced design positive displacement meters available. The complete family of top-performing C700 meters, sizes 5/8" to 2", can be offered with a variety of registers and material configurations.
Electronic Register Poly Meter Specs Digital Reg Specs  

      
 
Kent / AMCO T-3000 Turbine Water Meters
The Kent / AMCO T3000 is a high velocity Class II Turbine Meter exceeding AWWA Standard C-701.  Performance and simplicity are incorporated into the T3000 design.  The T3000's throated inlet increases low flow sensitivity, assuring high accuracy with low pressure loss.  This design also provides space between the rotor and chamber wall to allow passage of the suspended solids commonly seen in large meter installations.  For higher accuracy, in-line straightening vanes reduce turbulence.  The T3000's undergear assembly reduces the speed of the driving magnet, preventing magnetic breakaway during acceleration, maximizing usage registration.  The T3000 design is modular, facilitating maintenance by allowing replacement of the measuring element without removing the meter from service.   High quality materials, including a tungsten carbide rotor shaft, PTFE (Teflon) radial bearings, ceramic jewel thrust bearings and stainless steel body trim, combine to maximize service life. Available in bronze from 1 1/2 - 8" with various pulser and register options.
 
Strainers
Installation Specs
 
Kent / AMCO H4000 Bi-Directional Turbine Water Meters

The H4000, sizes 1½'' through 12'', is an inferential cold-water meter with a rotor that measures accurately in either direction, driving the rotor in direct proportion to the velocity of the water passing through the meter. The H4000 is recommended for industrial monitoring of high flows of cold water (less than 120° F) for direct read, remote totalization, and batching and continuous processes for rate of flow and bi-directional flows.

Specs
 
Kent / AMCO R1000 Propeller Water Meters

The R1000, sizes 2'' to 10'', is designed for measurement of high flows of cold water, in-plant applications for dirty water, standard agriculture, river and lake pumping applications as well as normal irrigation applications for water resource management.

 
Kent / AMCO C-3000 Compound Water Meters
Unparalleled accuracy in measuring a wide range of flows. The C-3000 compound meter combines all the great features of the T-3000 turbine meters and C-700 piston meters to form a true high performance Class II meter.

The COMBO meter is designed for the highest possible metering accuracy in installations where externally large variations in flow are typical such as schools, hospitals, shopping centers, and other installations where flow demands vary from a few drops to large peak-hour demands. 
The C-3000 Saves Money. Because the COMBO is lighter and less bulky, it does not require special equipment and additional labor to install. All C-3000 parts and subassemblies are completely interchangeable with the T-3000 turbine meter and the C-700 positive displacement meter, thereby eliminating dual inventory and cutting maintenance costs. 

 The C-3000 features a unique changeover valve. This spring loaded poppet style valve functions on differential pressure, and is a positive action valve, which means that it is fully opened or fully closed at all times. This superior design assures the highest accuracy (100% ± 1/2%) and eliminates the loss of revenue at changeover which is common with weighted check valves.

2" specs 8" specs

 
Kent / AMCO H-3200 Fire Hydrant Water Meters
The H-3200 Fire Hydrant Meter is ready to deliver high performance, high revenue capabilities and convenience. 

 The rugged H-3200 fire hydrant meter is a high performance Class II turbine meter ideal for temporary metering of well pumping, irrigation, construction, testing and other similar nonpermanent applications.   

 The H-3200 has a standard flow restrictor plate, which limits maximum output to 400 gpm to protect the meter from overspeeding. Or you may select the optional internal check valve, installed in place of the restrictor plate, that serves as a flow suppression device as well as a nonreturn valve and adds no weight or length to the meter. Another option is a gate valve which allows the operator to regulate the flow from the hydrant. 

 Light weight & easy to handle. The light weight aluminum body is fitted with inlet and outlet 2 1/2" NST national fire standard hose couplings, with a removable delrin plastic screen in the inlet coupling to prevent rotor damage from large particles. Convenient removable steel carrying handles act as a "roll bar" to protect the register and can easily be replaced. 

The H-3200 is built tough to withstand rough usage. One of the many advantages is the interchangeable parts and subassemblies used in the  T-3000 turbine meter and C-3000 compound meter, guaranteeing spare parts availability and low maintenance costs. 

Specs

 
Kent / AMCO Chemical PVDF Meters
PVDF Turbines, sizes ½'' and 1'' are designed for those applications where a more rugged meter is required. This unit retains all of the capabilities of the 316 SS Turbine Meter, plus the PVDF (Kynar) material and ceramic shaft allow use with approximately 100 more chemicals than stainless steel.

The unit is Factory Mutual (FM) approved and carries a Class 1, Division 1, Groups A-G Approval for hazardous environments.

1/2", 1" specs Pulse Access Module specs
 
Kent / AMCO Chemical 316 SS Turbine Meters
316 Stainless Steel Turbine meters, in sizes ½'' to 2'' for flows from 0.5 gpm to 1500 gpm, address a wide range of industrial and commercial fluid measuring applications. Meters can operate in high pressure (up to 1500 psi) applications.

Meters can be equipped with accessories for use with remote counters, batch controllers, rate transmitters, direct to chart recorders or computers.

1/2", 3/4", 1" specs Pulse Access Module specs
 
Kent / AMCO Precision Sanitary Stainless Steel Turbine Meters
Stainless Steel Precision Turbine Meter This line of 0.5% accuracy turbine meters is appropriate for a wide varity of flow applications.  Choose among the connection and output variants to get the meter best suited to your needs. Ideal for food and dairy processing, beverage manufacturing and pharmacuetical production.

Available with NPT, ANSI flange or sanitary clamp ends.

The construction material offer compatibility with a wide range of industrial process chemicals. Outputs include sine wave frequency pulse, conditional square wave pulse or blind 4-20mA analogue signal. As with other inferential turbine metering technologies, installation requirements must be observed for the best accuracy.

Sanitary Clamp specs
 
Kent / AMCO Electronic Accessories
Electronic Registers are available for all cold water Positive Displacement and Turbine Meters. The battery powered Electronic Register is designed to replace mechanical registers with LCD displays of rate indication and totalization in the basic unit.

The EBC2C is an AC powered totalizer, rate indicator, and batch controller. It has both single relay output to a standard solenoid and dual relay output for use with dual valve batch control systems, dual stage solenoids, or bi-directional solenoids with auxiliary limit switches.

Designed to operate with any AMCO meter equipped with pulse output, the AC powered Model R420 Rate Indicator/ Transmitter/Totalizer displays flow rate, totalization, high/low set points and supplies a 4-20 mA DC signal and four electronic outputs for driving electromechanical devices.

The Model R10 Rate Indicator/Totalizer is an economical battery-powered up-counting totalizer and a 1/Tau rate meter, with an 8-digit LCD display. Separately programmable count/rate scalers and decimal points allows for display of Rate and Count in various engineering units.

Electronic Batch Controller (EBC2C) specs R420 with 4-20mA Output Rate / Totalizer specs
 
Kent / AMCO Magnetic Water and Waste Meters
AquaMaster revolutionizes high volume electronic water measurement. Available in sizes 5/8" to 24", the rugged AquaMaster is designed to maximize revenue collection by offering a broad flow range with high accuracy, retention of high accuracy without testing or parts replacement, low-cost, foolproof installation, optional data logging capability and battery or mains-powered models to accommodate site requirements.

The MagMaster is an electromagnetic water and waste meter operating on Faraday's principle of induction. MagMaster covers the full flow range of most mechanical meters with a high accuracy. MagMaster is available in sizes 2 to 12 with industry standard 4-20 mA output of rate of flow data.

Aquamaster specs Aquamaster S specs Aquamaster Installation specs
MagMaster specs
 
back to the main kent / amco water meter page


watermeters.com
the first and still the best online source for water meters

Daniel L. Jerman Co.
275 Railroad Place
Hackensack, NJ 07601
Phone 800.654.3733
Fax 201.487.3953
International Phone 201.487.7444
email: sales@watermeters.com